E30/E36/Z3 95A poly centered front control arm bushings
Did you know we price match?
BMW E30, E36, Z3 POLY
CENTERED FRONT CONTROL ARM BUSHINGS (95a)
WHAT ARE 95a POLY CENTERED FRONT CONTROL ARM BUSHINGS AND WHY DOES MY E30, E36, Z3 NEED THEM?
The front control arms bushings on your E30, E36,or Z3 are one of the most common neglected parts on the front end of your BMW. They go bad from wear and tear, age, oil, and everything in between. Changing out your worn factory units to our 95a version will add stability, eliminate wheel hop and last a lifetime. If you're looking to tighten up your steering but not something as intense as derlin. 95a is the hardest poly available. It will be quieter then delrin but harder then our 80a series poly. This is the centered version that came on NON-M e30s, e36s. We also have offset versions available that were commonly found on E30 m3s and some E36 M3 models as well.
These simply get pressed into your OEM lolipop mounts and your in for precise handling. These will make a massive difference in front end grip and steering response. The factory rubber bushing was designed for comfort, not performance. They allow the control arm bushing to "float" in the center. That's great to keep the noise down, but allows for TONS of play in the steering. Using Garagistic poly CABs improves performance by reducing deflection. Poly bushings also have a much greater longevity than rubber bushings. Includes everything needed for installation. You will get two front control arm bushings. These are the "centered" bushings. If you would like the offset front control arm bushings (found in the e30 m3 and e36 m3) then click here. We highly recommend professional installation as these will require a press to install as well as remove your old bushings. Comes with a lifetime warranty. Price is for a pair (2 units) of Garagistic front control arm bushings. Enough to do 1 car.
WILL THESE 95A CENTERED POLY CONTROL ARM BUSHINGS FIT MY BMW?
REPLACES BMW OEM NUMBER: 31129069035 (31-12-9-069-035)
- E30 (318, 323, 325 & M3)
- Will also fit 318ti models
- Z3 models.
WHY SHOULD I REPLACE THE FRONT CONTROL ARM BUSHINGS ON MY E30, E36,OR Z3?
At the age of these e30s, the rubber front control arm bushings are often very worn and beat up. When you go over a bump the front wheel will shimmy and hop and do all kinds of weird business. Most people do not realize that these are a maintenance item and should really be done before lowering the vehicle. These 95a poly bushing options are the ultimate in dual purpose performance. They are great for full dedicated track use because noise exhaustion will not be there compared to its delrin counterpart. They WILL increase road noise very slightly if used on a street car (because they are solid geometry). Price for 1 pair of front-control arm bushings.
WHY USE POLY OVER DERLIN BUSHINGS IN MY E30, E36, OR Z3?
Well we will start by mentioning that the factory bushings we made of rubber (duh!). That means the BMW put them there because they are designed to flex and absorb energy making it a little comfy on the street and not allowing a sh** ton of noise to get in). That's wonderful if your car is a street car, but on an all out track rat, drift car, or full out race car build you want your alignment to stay constant. Get it? Flex = the enemy. That makes Delrin the ultimate bushing for all out race vehicles. It is incredibly strong, has no flex, and low coefficient of friction. However it makes alot of noise into the cabin of the car. This is where Poly becomes a better choice in some cases. It still overs the same non-existant suspension bushing deflection delrin does without he noise. No deflection means no geometry change. If you are looking for a compromise between delrin and rubber, then check out our poly line. We offer them in a few flavors to suit your needs from OEM+, to dual purpose street/autox/track cars. Keep in mind that both Poly and Delrin will outlast your OEM rubber bushings.